BMW F 650 GS Twin Accessories

With the help of handlebar risers and handlebar risers with offset, you can adjust the seating position on the motorbike to suit you and therefore ride in a more relaxed and comfortable manner. The handlebar risers and handlebar relocations fit seamlessly and unobtrusively into the overall line of the motorbike. simple installationNaturally TÜV-tested and incl. ABEhigh qualityvarious designs depending on the model: Distances or sleeves under the handlebar clamps; handlebar risers under the handlebars for use with original upper clamp; handlebar risers with lower and upper clamps

Let there be light! Motorbike auxiliary headlights LED NOVA With the Nova LED auxiliary headlight set from HEPCO&BECKER, you get everything you need to improve the visibility and safety of your motorbike. This set includes powerful LED auxiliary headlights, a universal mounting set, a cable set, a switch, instructions and a tool set to conveniently mount and control the headlights. The Nova LED auxiliary headlights not only provide improved illumination of the road, but also give your motorbike an attractive appearance. Easy installation is made possible by the universal mounting kit and cable set supplied. Increase your safety and add an appealing design to your motorbike by using the HEPCO&BECKER LED motorbike auxiliary headlight set Nova. The brand new LED auxiliary headlight Nova - the next step in lighting technology. High-power LEDs with two switching levels at 2,500lm - 4,350K / - 5,500K 12 volt, 25 watts per headlight ECE-tested and approved, so no individual approval is required (observe country-specific legal regulations for installation) Improved lighting conditions in road traffic Universal mounting on engine or tank protection bracket with Ø18mm - Ø25mm tube, can be mounted upright or suspended complete headlight set; incl. 2x LED auxiliary headlights, 1x switch, 1x cable set, 2x clamps incl. reduction sleeves, 1x instructions, 1x tool set Connection only via the battery, no connection to vehicle wiring harness required No third-party operation thanks to special control unit with automatic voltage control Waterproof and dustproof to IP67Headlights can be added flexibly via the switch on the handlebarsPlease note: The lights can only be switched on approx. 5-15 seconds after starting the engine. A voltage of at least 13.1 V must be applied to the control unit of the wiring harness to enable the circuit . In older vehicles, this can be achieved by briefly increasing the speed. Switching off must be done manually at the switch. The NOVA LEDs remain lit until the voltage limit of 11.8 V is reached, even after the engine has been switched off. Only when falls below this voltage limit do the lights switch off automatically via the control unit. When switching on again (wait for the dwell time of the control unit), the voltage limit of 13.1 V is queried again. Download FAQ as PDF

Engine protection: crash bar for BMW F 650 GS Twin from Hepco & Becker Whether you prefer to ride off-road, even in difficult terrain, freely on the country road or spend most of your time in the city, a motorbike crash bar is no longer a beginner's accessory. Developed for a wide range of motorbikes, our crash bars fit perfectly into the existing lines of your BMW F 650 GS Twin and give the motorbike a characteristic look, but more than just that: in the event of a crash or unintentional ground contact, our motorbike crash bars also protect the rider from more serious damage! Crash bars from Hepco&Becker are the right choice for all individualists who value safety and quality. Made from an extremely stable tube-in-tube construction, manufactured from German quality steel or stainless steel, they offer maximum protection - with many newer models already featuring an integrated crash pad.Exclusive look thanks to high-quality surface finish: High-quality powder coating from Germany.And last but not least, motorbike crash bars also offer you many other options for additional comfort, for example you can attach our protective bar bags to them, or our additional/fog lights.On top of this, motorbike crash bars are incredibly well suited for securely lashing your bike to a trailer if you ever need to transport it. Features & details: Material: Tubular steel made in GermanySurface finish: High-quality powder coatingColour: RedFor model year(s): 2008-2011Provides effective protection in the event of minor accidents or mishaps Extremely helpful when lashing the motorbike, e.g. on trailers Scope of delivery: Engine guard for BMW F 650 GS Twin leftEngine guard for BMW F 650 GS Twin right Screw set (incl. spacers, sleeves, washers etc.) Multilingual, comprehensive illustrated assembly instructions Important notes: No ABE or registration is required for this product if fitted as intended Please observe the model-specific information listed in the installation instructions and properties! Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! For safety reasons, all mudguards should be adequately checked after a crash and replaced if necessary. If original or accessory parts have already been fitted, there may be restrictions; these can be found in the fitting instructions. We offer special conditions for official driving schools. Please contact our customer service at (+49) 0 6331 / 1453 - 222

Engine protection: crash bar for BMW F 650 GS Twin from Hepco & Becker Whether you prefer to ride off-road, even in difficult terrain, freely on the country road or spend most of your time in the city, a motorbike crash bar is no longer a beginner's accessory. Developed for a wide range of motorbikes, our crash bars fit perfectly into the existing lines of your BMW F 650 GS Twin and give the motorbike a characteristic look, but more than just that: in the event of a crash or unintentional ground contact, our motorbike crash bars also protect the rider from more serious damage! Crash bars from Hepco&Becker are the right choice for all individualists who value safety and quality. Made from an extremely stable tube-in-tube construction, manufactured from German quality steel or stainless steel, they offer maximum protection - with many newer models already featuring an integrated crash pad.Exclusive look thanks to high-quality surface finish: High-quality powder coating from Germany.And last but not least, motorbike crash bars also offer you many other options for additional comfort, for example you can attach our protective bar bags to them, or our additional/fog lights.On top of this, motorbike crash bars are incredibly well suited for securely lashing your bike to a trailer if you ever need to transport it. Features & details: Material: Tubular steel made in GermanySurface finish: High-quality powder coatingColour: BlackFor model year(s): 2008-2011Provides effective protection in the event of minor accidents or mishaps Extremely helpful when lashing the motorbike, e.g. on trailers Scope of delivery: Engine guard for BMW F 650 GS Twin leftEngine guard for BMW F 650 GS Twin right Screw set (incl. spacers, sleeves, washers etc.) Multilingual, comprehensive illustrated assembly instructions Important notes: No ABE or registration is required for this product if fitted as intended Please observe the model-specific information listed in the installation instructions and properties! Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! For safety reasons, all mudguards should be adequately checked after a crash and replaced if necessary. If original or accessory parts have already been fitted, there may be restrictions; these can be found in the fitting instructions. We offer special conditions for official driving schools. Please contact our customer service at (+49) 0 6331 / 1453 - 222

Tank protection: crash bar for BMW F650GS Twin(2008-2011)F700GS(12-17)F 800 GS from Hepco & Becker Whether you prefer to ride off-road, even in difficult terrain, freely on the country road or spend most of your time in the city, a motorbike crash bar is no longer a beginner's accessory. Developed for a wide range of motorbikes, our crash bars fit perfectly into the existing lines of your BMW F650GS Twin(2008-2011)F700GS(12-17)F 800 GS and give the motorbike a characteristic look, but more than just that: in the event of a crash or unintentional contact with the ground, our motorbike crash bars also protect the rider from more serious damage! Crash bars from Hepco&Becker are the right choice for all individualists who value safety and quality. Made from an extremely stable tube-in-tube construction, manufactured from German quality steel or stainless steel, they offer maximum protection - with many newer models already featuring an integrated crash pad.Exclusive look thanks to high-quality surface finish: High-quality powder coating from Germany.And last but not least, motorbike crash bars also offer you many other options for additional comfort, for example you can attach our protective bar bags to them, or our additional/fog lights.On top of this, motorbike crash bars are incredibly well suited for securely lashing your bike to a trailer if you ever need to transport it. Features & details: Material: Tubular steel made in GermanySurface finish: High-quality powder coatingColour: BlackFor model year(s): 2008-2016Provides effective protection in the event of minor accidents or mishaps Extremely helpful when lashing the motorbike, e.g. on trailers Scope of delivery: Tank guard for BMW F650GS Twin(2008-2011)F700GS(12-17)F 800 GS leftTank guard for BMW F650GS Twin(2008-2011)F700GS(12-17)F 800 GS right Screw set (incl. spacers, sleeves, washers etc.) Multilingual, comprehensive illustrated assembly instructions Important notes: No ABE or registration is required for this product if fitted as intended Please observe the model-specific information listed in the installation instructions and properties! Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! For safety reasons, all mudguards should be adequately checked after a crash and replaced if necessary. If original or accessory parts have already been fitted, there may be restrictions; these can be found in the fitting instructions. We offer special conditions for official driving schools. Please contact our customer service at (+49) 0 6331 / 1453 - 222

Tank protection: crash bar for BMW F650GS Twin(2008-2011)F700GS(12-17)F 800 GS from Hepco & Becker Whether you prefer to ride off-road, even in difficult terrain, freely on the country road or spend most of your time in the city, a motorbike crash bar is no longer a beginner's accessory. Developed for a wide range of motorbikes, our crash bars fit perfectly into the existing lines of your BMW F650GS Twin(2008-2011)F700GS(12-17)F 800 GS and give the motorbike a characteristic look, but more than just that: in the event of a crash or unintentional contact with the ground, our motorbike crash bars also protect the rider from more serious damage! Crash bars from Hepco&Becker are the right choice for all individualists who value safety and quality. Made from an extremely stable tube-in-tube construction, manufactured from German quality steel or stainless steel, they offer maximum protection - with many newer models already featuring an integrated crash pad.Exclusive look thanks to high-quality surface finish: High-quality powder coating from Germany.And last but not least, motorbike crash bars also offer you many other options for additional comfort, for example you can attach our protective bar bags to them, or our additional/fog lights.On top of this, motorbike crash bars are incredibly well suited for securely lashing your bike to a trailer if you ever need to transport it. Features & details: Material: Tubular steel made in GermanySurface finish: High-quality powder coatingColour: RedFor model year(s): 2008-2016Provides effective protection in the event of minor accidents or mishaps Extremely helpful when lashing the motorbike, e.g. on trailers Scope of delivery: Tank guard for BMW F650GS Twin(2008-2011)F700GS(12-17)F 800 GS leftTank guard for BMW F650GS Twin(2008-2011)F700GS(12-17)F 800 GS right Screw set (incl. spacers, sleeves, washers etc.) Multilingual, comprehensive illustrated assembly instructions Important notes: No ABE or registration is required for this product if fitted as intended Please observe the model-specific information listed in the installation instructions and properties! Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! For safety reasons, all mudguards should be adequately checked after a crash and replaced if necessary. If original or accessory parts have already been fitted, there may be restrictions; these can be found in the fitting instructions. We offer special conditions for official driving schools. Please contact our customer service at (+49) 0 6331 / 1453 - 222

Motorbike underride guard: engine protection plate for BMW F 650 GS Twin (2008-2011), silver Even a pavement can mean unpleasant and heavy contact with the ground, which can lead to damage to the engine housing. Our engine protection plates protect the manifold and the engine block from impacts and stone chipping, even with the heaviest ground contact. With our underride guard for F 650 GS Twin, you not only upgrade your motorbike in terms of safety, but also automatically give it a certain off-road look. Naturally manufactured specifically for each model from approx. 4 mm thick, high-strength aluminium, our Hepco&Becker engine protection plate lets enough air through for cooling thanks to its special shape and is naturally angled, so that water such as rainwater or splash water is drained to the outside, thus providing additional protection against rust formation. It enhances the look of your motorbike and is guaranteed never to let you down Features & important details: Material: High-strength aluminium, made in Germany Surface finish: Brushed, anodised Colour: Silver anodisedFor model year(s): 2008-2011Provides additional protection for sensitive parts on the manifold and engine block Scope of delivery: Engine protection plate for BMW F 650 GS TwinMounting material / screw set Illustrated installation instructions (DE / EN) Important notes: No ABE or registration is required for this product if fitted as intended Please observe the fitting instructions and model-specific information to determine whether there may be any restrictions. Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! Restrictions may apply to original parts or accessories that have already been fitted; these can be found in the fitting instructions.

Grip guard for BMW F 650 GS Twin & F 800 GS - from Hepco&Becker The Hepco&Becker grip guard ensures reliable protection for the rider's hands and the motorbike handlebars both when riding off-road and on asphalt. Model-specific hand protector guard for your BMW F 650 GS Twin or F 800 GS- Tubular steel construction precisely customised to your motorbike for the perfect look. Ideal for all adventure bikes to stabilise the hand protectors and protect them from breakage in the event of a fall or contact with a large branch, for example! Reliable, robust protection for the handlebar fittings in the event of a fall with optimum aerodynamics. As individual as you are - make it your bike! Details & features: Material: Tubular steel, made in Germany Surface finish: High-quality, colour-matching powder coating Colour: black For model years: F 650 GS Twin: 2008-2011 & F 800 GS: 2008-2018 Scope of delivery: 1 set of grip guards (left & right) Complete set of mounting material Bilingual, illustrated assembly instructions Important notes: The plastic hand protectors shown in the pictures are part of the delivery condition of the motorbike, they are NOT included! Please observe the model-specific information listed in the fitting instructions and the features! Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! May not fit in combination with non-original handlebar clamps, e.g. with comfort handlebars or handlebar risers! For safety reasons, all protective bars should be adequately checked after a fall and replaced if necessary.

For selected motorbike models frequently used in riding schools, from 125cc to 750cc, we offer special front and rear guards that can be combined with our engine guards.good protection in the event of falls and crashes at low speedsTurn signals, clutch and brake levers, exhaust silencers, fairing parts etc. are effectively protectedhigh-quality powder coatingincl. mounting materialWe offer special conditions for driving schools. Please get in touch with our contact persons. Tel: 06331/1453-222 or mail: shop@hepco-becker.de

For selected motorbike models frequently used in riding schools, from 125cc to 750cc, we offer special front and rear guards that can be combined with our engine guards.good protection in the event of falls and crashes at low speedsTurn signals, clutch and brake levers, exhaust silencers, fairing parts etc. are effectively protectedhigh-quality powder coatingincl. mounting materialWe offer special conditions for driving schools. Please get in touch with our contact persons. Tel: 06331/1453-222 or mail: shop@hepco-becker.de

Our Hepco&Becker lamp guard protects the headlight in many cases and also gives your bike the proper off-road look.adapted to the design of the motorbikeeffective protectionno reflections or danger from glaresimple mounting on mostly existing screw pointssolid construction made from German steelrobust and high-quality coatingmade in Germany without TÜV

Side stand extension BMW F 650 GS (2008-2011) For widening the contact surface of the side stand - for absolutely secure standing on gravel, sand, crushed stone, etc. Quick and easy to fit, made from high-quality CNC-milled aluminium with a powder-coated steel counter bracket - Made in Germany. Especially when fully loaded or on unpaved surfaces, the motorbike on the side stand can easily sink and tip over. To free your motorbike from this danger, we recommend a model-specific, moulded side stand plate from Hepco&Becker. The side stand support is enlarged to approximately double the surface area compared to the original stand, so your F 650 GS is perfectly protected against accidents when parking. Material: Aluminium & powder-coated steel Colour: silver / black Developed specifically for the BMW F 650 GS For model year(s): 2008, 2009, 2010, 2011 Effective protection when parking Quick and easy installation with just a few screws ABE & registration free

Stable. Stable. Easy to use. The centre stands from Hepco&Becker usually do not restrict the rider's lean angle and are extremely robust. Thanks to the sophisticated geometry and non-slip tread surface, it is very easy to park the motorbike safely in any situation.The precisely manufactured stands are very stable, sandblasted, primed and black powder-coated and therefore weatherproof and stable in value. Main stands simplify maintenance work and ensure a secure stand, e.g. when refuelling. They relieve the load on the suspension elements and the rear wheel during winter storage.ABE is suppliedusually no restriction on lean angle clearancehigh-quality surface finishScope of delivery: Main stand + mounting material + instructionsplease note the installation instructions providedHelpful tool for attaching the tension spring: item number: 700030

Basic tank ring for BMW F 800 GS Adventure / F 800 GS (2008-2018) / F 700GS (2012-) / F 650 GS (34 hp version) (2008-) / G 650 GS (2011-2016)Simple and innovative at the same time - our BASIC tank ring This functional tank ring enables the attachment of a tank bag from Hepco&Becker.The scope of delivery includes a BASIC tank ring and the counterholder, which can be individually screwed to the tank bag depending on the tank shape and handlebar angle. The tank cap can still be opened without any problems when the tank ring is fitted. In general, you only need this tank ring and a tank bag for BMW F 800 GS Adventure / F 800 GS (2008-2018) / F 700GS (2012-) / F 650 GS (34 hp version) (2008-) / G 650 GS (2011-2016) and you have everything you need. Each model-specific tank ring is stored in the "My Bike" database for the respective motorbike model. If no tank ring is stored, you can also use the checklist here in the shop to find out manually whether a universal tank ring is available for the desired model. (See main menu -> BASIC tank rings) FEATURES: absolutely secure hold, even at high speeds Simple operation thanks to mechanical locking the Hepco&Becker tank bag is simply put on and locks clearly audible on the tank ring Unlocking: The mechanism is unlocked by a strap in the direction of travel at the front of the tank bag and the tank bag is then simply removed No ABE or registration is required for this product when fitted as intended Recommended maximum speed when the tank bag is fitted: 130 km/h Recommended load in the tank bag: approx. 3kg Please observe the motorbike manufacturer's specifications and the model-specific information in the instructions or here with the product Difference between Lock-it and BASIC tank rings: The general function and operation remain the same. However, compared to the Lock-it tank ring, the Basic tank ring only locks mechanically. With the Lock-it tank ring, the magnets help with centring. The difference lies purely in the two magnetic or plastic domes that are screwed onto the tank ring. The actual model-specific "metal ring" is the same for both versions. Further information: A tank bag with Lock-it counterholder cannot be fitted to a BASIC tank ring and vice versa. The tank bag counterholder and tank ring must be from the same system.

C-Bow side bag holder for BMW F 650 GS Twin (2008-2011)/F700GS (2012-2017)/F 800 GS (2008-2018) is designed to accommodate a wide range of Hepco&Becker Bags. Softbags for sporty, dynamic motorbikes and saddlebags for choppers and cruisers can be attached to the motorbike with the C-Bow holder. Its elegant, unobtrusive design blends in perfectly with the overall lines of the vehicle. Naturally, it keeps the saddlebags safely away from the hot exhaust silencer. Thanks to modern C-Bow technology, the matching bags can be attached to the C-Bow simply and easily with just one click and locked to prevent theft. The bags are securely fastened to the motorbike and remain in position even when loaded. On many models, the indicators remain in their original position. Further information can be found in the fitting instructions.solid side carrier for mounting Hepco&Becker C-Bow side bags and panniershigh-quality surface finishnormal Hepco&Becker hard cases such as the Junior or Journey do not fit!Krauser K-Wing cases do not fit on the C-Bow carrier!Recommended payload: 5kg per bag/case (please observe the assembly instructions, vehicle-specific information and motorbike manufacturer's specifications for any restrictions that may apply)can usually be combined with top case carriers, sissy bars or solo racks without any problems (please observe the installation instructions or the vehicle-specific information for the respective carrier)Luggage rack extensions can restrict bag mounting on the carrierNo ABE or registration is required for this product if fitted as intendedScope of delivery: left, right, mounting material and instructionsDeveloped for the standard condition of the machine. Not tested with accessories such as exhaust, licence plate holder or other indicators. Make sure that the bags always have sufficient distance to the exhaust and that the indicators have a sufficient beam angle. The exhaust jet must not be directed at the bags.

The bolt-on side case carriers from Hepco&Becker are firmly attached to the motorbike frame. Almost all Hepco&Becker touring side case systems fit onto this carrier. The cases are secured to the carrier using a metal retaining lock to prevent theft. A lock adapter is also required for this. This is normally supplied with the side cases. This lock adapter is screwed to the right and left at the rear of the carrier and provides the mount for the case retaining lock.The model-specific carriers are solidly designed and offer effective protection for the rider's or pillion passenger's legs even in the event of a fall.The side case carriers from Hepco&Becker can usually be combined with our rear carriers without any problems. Please refer to the fitting instructions and the model-specific information.Tubular steel construction MADE IN GERMANYfirmly bolted to the motorbike framehigh-quality surface finishFits most Hepco&Becker hard-shell side cases (please refer to the model-specific instructions for the respective carrier for any restrictions that may apply)Indicators usually remain in their original position, but sometimes have to be moved to ensure a certain beam angle (please refer to the installation instructions for the product)Scope of delivery: right + left incl. mounting material and instructionsLuggage systems generally do not require an ABE or registrationTube diameter: 16 mm

Case carrier set for BMW F 700 GS (2012-2017) incl. Xplorer motorbike case, blackSet consisting of a double-sided, motorbike model-specific stainless steel case carrier in combination with an Xplorer 40 and a recessed Xplorer 37 side case incl. key, lock cylinder and the lock adapters required to attach the cases to the carrierMotorbike side case features:recessed 37 litre case on the end pot side40 litre case on the other sidehighly impact-resistant plastic and anodised aluminium sheets in combinationincl. key and cylinderabsolutely watertight thanks to integrated rubber seal in the lidextensive range of accessories available (inner bags, top bags, etc.)Motorbike luggage carrier features:adventure-ready, weather-resistant and bolted stainless steel pannier rackblasted and electropolished surface finishincl. mounting material and assembly instructions

Case carrier set for BMW F650/700GS incl. Xplorer motorbike case, silverSet consisting of a double-sided, motorbike model-specific stainless steel case carrier in combination with an Xplorer 40 and a recessed Xplorer 37 side case incl. key, lock cylinder and the lock adapters required to attach the cases to the carrierMotorbike side case features:recessed 37 litre case on the end pot side40 litre case on the other sidehighly impact-resistant plastic and anodised aluminium sheets in combinationincl. key and cylinderabsolutely watertight thanks to integrated rubber seal in the lidextensive range of accessories available (inner bags, top bags, etc.)Motorbike luggage carrier features:adventure-ready, weather-resistant and bolted stainless steel pannier rackblasted and electropolished surface finishincl. mounting material and assembly instructions

The Easyrack top case carrier in an elegant black finish was specially developed for the BMW F 650 GS Twin (2008-2011) and the F 700 GS (2012-2017). This carrier consists of a model-specific mounting kit and the Easyrack adapter plate to attach Hepco&Becker top cases or soft luggage (not suitable for top cases with a universal plastic plate). Each Easyrack top case carrier is designed with a model-specific approach to fit seamlessly into the overall appearance of the motorbike. By using high-quality aluminium in combination with a steel base carrier, the Easyrack combines high strength with an elegant look. The design of the rack integrates additional attachment points for luggage straps, for example to securely attach luggage rolls. The basic construction is made of sturdy steel and an aluminium carrier plate, which ensures stability and reliability. The scope of delivery includes the model-specific Easyrack top case carrier, an installation kit and detailed installation instructions. Additional adapters for the top case attachment are not required. The surface finish is of high quality. In technical terms, the Easyrack top case carrier works in a similar way to the Alurack top case carrier. One difference is that the bracket for holding the top case on the Easyrack can be folded in when not in use, whereas the Alurack bracket stands rigidly upwards. The model-specific base carrier is the same for Easyrack and Alurack. No additional ABE or registration is required for the luggage carriers. The recommended load is 5 kg (please observe the model-specific instructions, assembly instructions and information provided by the motorbike manufacturer). Heavy luggage should generally be stowed in the side cases or the tank bag. The recommended maximum speed is 130 km/h. The Easyrack top case carrier was developed for the standard condition of the bike and has not been tested with accessories such as exhaust, licence plate holder or other indicators.

Top case carrier consisting of a model-specific mounting kit and the Alurack adapter plate for mounting Hepco&Becker top cases or soft luggage (not suitable for top cases with universal plastic plate) Each Alurack top case carrier is developed specifically for each model and therefore blends in with the harmonious overall appearance of the motorbike. Thanks to the production from high-quality aluminium in combination with a steel base carrier, the Alurack has high strength and a very elegant appearance. Additional attachment points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack.solid basic construction made of steel and an aluminium carrier plateScope of delivery: model-specific aluminium top case carrier + mounting kit + mounting instructionsno additional adapters are required for top case mountinghigh-quality surface finishtechnically, it works almost the same as the Easyrack top case carrier, except that the bracket for the top case mount is fixed at the top and cannot be folded downthe model-specific base carrier is the same for the Easyrack and Aluracka special bracket is required to mount the Hepco&Becker aluminium standard top case 35 instead of the normal Alurack bracket (article number: 700007350 or 700007351)Luggage racks do not require an ABE or registrationRecommended payload: 5kg payload (please observe model-specific information, the stored assembly instructions and motorbike manufacturer information)Note: Heavy luggage should generally not be transported in the top case, but in the side cases or the tank bag.Recommended maximum speed: 130 km/hDeveloped for the standard condition of the machine. Not tested with accessories such as exhaust, licence plate holder or other indicators.

Proven tubular luggage racks Top case carriers for Hepco&Becker top cases of the highest quality. Hepco&Becker luggage racks are specially designed for almost all of our top cases. But not only new top cases fit. Older Hepco&Becker models can also be fitted. The basic mounting has not changed. Not suitable for: Topcase "Orbit" and topcases with universal plate. The carriers are manufactured specifically for each model and only fit the motorbike listed in the fitting instructions. Thanks to the construction made of German quality steel, Hepco&Becker luggage racks guarantee maximum strength and a very high level of safety. If required, soft luggage can also be lashed down without any problems, the tubular luggage rack offers many options for this. If there is still not enough space, the luggage rack can be combined with the Hepco&Becker universal luggage rack extension. The top case is pushed onto the tubular luggage rack and locked to the carrier with a metal retaining lock. Recommended payload: approx. 5kg (Please observe the model-specific information on the respective carrier as well as the motorbike manufacturer-specific information) Can usually be combined with side case carriers or C-Bow holders without any problems (follow the fitting instructions) Incl. mounting material and instructions MADE IN GERMANY Luggage carriers generally do not require an ABE or registration

Sturdy aluminium plate for widening on almost all luggage racks with a straight support surface if loose luggage is to be transported rather than a top case. The raised edges and additional retaining points make the extension ideal for safely transporting larger luggage rolls, travel bags, tents, duffle bags, etc.Aluminium construction with high strength and high-quality appearanceFastening options for strapsNot suitable for topcase mountingincludes assembly material and instructionshigh-quality plastic coatingRecommended load: 5kg (Please observe the model-specific instructions and the motorbike manufacturer's specifications. Heavy luggage should generally not be transported on the rear, but in the side cases or the tank bag.

Inner dimensions: 29x8 cm (length/diameter) Outer dimensions: 32x9 cm Volume: approx. 1.5 litres mounted on the inside of a side case carrier to utilise this space for specific models a model-specific mounting kit is included as fastening material waterproof twist lock perfect for carrying tools, safety waistcoats or similar items.