MOTO-GUZZI V7 III Accessories
Here you will find all model-specific products available and accessories for MOTO-GUZZI V7 III
- Our crash bars for V7 III – protecting both your motorcycle and yourself
- The Twinlight auxiliary lights for improved visibility and enhanced safety
- Side case carriers as well as our patented C-Bow side carrier for V7 III
- The universal tank bag Epic 11 Belt
- The model-specific rear rack for MOTO-GUZZI V7 III
You will also find the corresponding luggage items with the respective carriers in the accessories section.
LED auxiliary headlights Nova (set) incl. Ø18-25mm universal mounting set, wiring harness and switch
Let there be light! Motorbike auxiliary headlights LED NOVA With the Nova LED auxiliary headlight set from HEPCO&BECKER, you get everything you need to improve the visibility and safety of your motorbike. This set includes powerful LED auxiliary headlights, a universal mounting set, a cable set, a switch, instructions and a tool set to conveniently mount and control the headlights. The Nova LED auxiliary headlights not only provide improved illumination of the road, but also give your motorbike an attractive appearance. Easy installation is made possible by the universal mounting kit and cable set supplied. Increase your safety and add an appealing design to your motorbike by using the HEPCO&BECKER LED motorbike auxiliary headlight set Nova. The brand new LED auxiliary headlight Nova - the next step in lighting technology. High-power LEDs with two switching levels at 2,500lm - 4,350K / - 5,500K 12 volt, 25 watts per headlight of course ECE-tested and approved, so no individual approval is required (observe country-specific legal regulations for installation) Improved lighting conditions in road traffic Universal mounting on engine or tank protection bracket with Ø18mm - Ø25mm tube, can be mounted upright or suspended complete headlight set; incl. 2x LED auxiliary headlights, 1x switch, 1x cable set, 2x clamps incl. reduction sleeves, 1x instructions, 1x tool set Connection only via the battery, no connection to vehicle wiring harness required No third-party operation thanks to special control unit with automatic voltage control Waterproof and dustproof to IP67Headlights can be added flexibly via the switch on the handlebarsPlease note: The lights can only be switched on approx. 5-15 seconds after starting the engine. A voltage of at least 13.1 V must be applied to the control unit of the wiring harness to enable the circuit . In older vehicles, this can be achieved by briefly increasing the speed. Switching off must be done manually at the switch. The NOVA LEDs remain lit until the voltage limit of 11.8 V is reached, even after the engine has been switched off. Only when falls below this voltage limit do the lights switch off automatically via the control unit. When switching on again (wait for the dwell time of the control unit), the voltage limit of 13.1 V is queried again. Download FAQ as PDF
Twinlight auxiliary headlight set (high beam) incl. holder and cable black for Moto Guzzi V7 III (Stone, Special, Anniversario, Racer) (2017-2020)
The Hepco&Becker Twinlights, with 2x55 watt light output, guarantee an impressive appearance. They are not only an attractive addition, but also offer added safety. Naturally TÜV-free and with type approval.are switched on instead of the normal high beamwhen the high beam is on, a maximum of two headlights may be lit on the motorbikesimple installationScope of delivery: headlight set, model-specific bracket and mounting materialincl. ABEincl. bulb (halogen bulb H3 with flat plug connection, 55 watts)
Engine guard black for Moto Guzzi V7 III (Stone, Special, Anniversario, Racer) (2017-2020)
Whether you spend most of your time travelling on rough terrain, on country roads or in the city, a crash bar from Hepco&Becker is always the right choice. Your motorbike is always effectively protected against unexpected mishaps.More than that: in the event of a crash or unintentional contact with the ground, you can protect the motorbike and the rider from major damage.The crash bars from Hepco&Becker perfectly trace the lines of the machine and thus give the motorbike an individual character. Made from an extremely sturdy tube-in-tube construction, some new models have an integrated crash pad.Various surface finishes are available depending on the vehicle model.protects against crashes and fallshelpful when lashing the motorbikehigh-quality metal coatingsolid construction, manufactured MADE IN GERMANY in our factory in Pirmasenscomprehensive and easy-to-understand assembly instructionsScope of delivery: right + left incl. mounting material and instructionsplease refer to the stored installation instructions or the vehicle-specific information for any restrictions or notes that may ariseno ABE or registration is requiredWe offer special conditions for official driving schools. Please contact our customer service Tel: (+49) 0 6331 / 1453 - 222
Chrome engine guard for Moto Guzzi V7 III (Stone, Special, Anniversario, Racer) (2017-2020)
Whether you spend most of your time travelling on rough terrain, on country roads or in the city, a crash bar from Hepco&Becker is always the right choice. Your motorbike is always effectively protected against unexpected mishaps.More than that: in the event of a crash or unintentional contact with the ground, you can protect the motorbike and the rider from major damage.The crash bars from Hepco&Becker perfectly trace the lines of the machine and thus give the motorbike an individual character. Made from an extremely stable tube-in-tube construction, some of the new models have an integrated crash pad.Various surface finishes are available depending on the vehicle model.protects against crashes and fallshelpful when lashing the motorbikehigh-quality metal coatingsolid construction, manufactured MADE IN GERMANY in our factory in Pirmasenscomprehensive and easy-to-understand assembly instructionsScope of delivery: right + left incl. mounting material and instructionsplease refer to the stored installation instructions or the vehicle-specific information for any restrictions or notes that may ariseno ABE or registration is requiredWe offer special conditions for official driving schools. Please contact our customer service Tel: (+49) 0 6331 / 1453 - 222
Centre stand black for Moto Guzzi V7 III (Stone, Special, Anniversario, Racer) (2017-2020)
Stable. Stable. Easy to use. The centre stands from Hepco&Becker usually do not restrict the rider's lean angle and are extremely robust. Thanks to the sophisticated geometry and non-slip tread surface, it is very easy to park the motorbike safely in any situation.The precisely manufactured stands are very stable, sandblasted, primed and black powder-coated and therefore weatherproof and stable in value. Main stands simplify maintenance work and ensure a secure stand, e.g. when refuelling. They relieve the load on the suspension elements and the rear wheel during winter storage.ABE is suppliedusually no restriction on lean angle clearancehigh-quality surface finishScope of delivery: Main stand + mounting material + instructionsplease note the installation instructions providedHelpful tool for attaching the tension spring: item number: 700030
Epic 11 Belt tank bag
Universal fit thanks to flexible belt fastening. For models for which we cannot offer a model-specific tank ring for technical reasons.Dimensionally stable thanks to high-density EVA foams, tear-resistant Hypalon and 840D ballistic polyester. Lockable zips Robust carrying handle Water-repellent outer material Additional compartments with mesh pocket inside the lid Small reflective details for better visibility in road traffic Removable, waterproof inner bag with roll-top fastening - easy removal with press stud fasteningVolume expansion through all-round zipLoops on the tank bag for attaching optional, customised accessories such as the Hepco&Becker map/smartphone bag
C-Bow side carrier black for Moto Guzzi V7 III (Stone, Special, Anniversario) (2017-2020)
C-Bow side bag holder for Moto Guzzi V7 III (Stone, Special, Anniversario) (2017-2020) is designed to accommodate a wide range of Hepco&Becker Bags. Softbags for sporty, dynamic motorbikes and saddlebags for choppers and cruisers can be attached to the motorbike with the C-Bow holder. Its elegant, unobtrusive design blends in perfectly with the overall lines of the vehicle. Naturally, it keeps the saddlebags safely away from the hot exhaust silencer. Thanks to modern C-Bow technology, the matching bags can be attached to the C-Bow simply and easily with just one click and locked to prevent theft. The bags are securely fastened to the motorbike and remain in position even when loaded. On many models, the indicators remain in their original position. Further information can be found in the fitting instructions.solid side carrier for mounting Hepco&Becker C-Bow side bags and panniershigh-quality surface finishnormal Hepco&Becker hard cases such as the Junior or Journey do not fit!Krauser K-Wing cases do not fit on the C-Bow carrier!Recommended payload: 5kg per bag/case (please observe the assembly instructions, vehicle-specific information and motorbike manufacturer's specifications for any restrictions that may apply)can usually be combined with top case carriers, sissy bars or solo racks without any problems (please observe the installation instructions or the vehicle-specific information for the respective carrier)Luggage rack extensions can restrict bag mounting on the carrierNo ABE or registration is required for this product if fitted as intendedScope of delivery: left, right, mounting material and instructionsDeveloped for the standard condition of the machine. Not tested with accessories such as exhaust, licence plate holder or other indicators. Make sure that the bags always have sufficient distance to the exhaust and that the indicators have a sufficient beam angle. The exhaust jet must not be directed at the bags.
C-Bow side carrier chrome for Moto Guzzi V7 III (Stone, Special, Anniversario) (2017-2020)
C-Bow side bag holder for Moto Guzzi V7 III (Stone, Special, Anniversario (2017-2020) is designed to accommodate a wide range of Hepco&Becker Bags. Softbags for sporty, dynamic motorbikes and saddlebags for choppers and cruisers can be attached to the motorbike with the C-Bow holder. Its elegant, unobtrusive design blends in perfectly with the overall lines of the vehicle. Naturally, it keeps the saddlebags safely away from the hot exhaust silencer. Thanks to modern C-Bow technology, the matching bags can be attached to the C-Bow simply and easily with just one click and locked to prevent theft. The bags are securely fastened to the motorbike and remain in position even when loaded. On many models, the indicators remain in their original position. Further information can be found in the fitting instructions.solid side carrier for mounting Hepco&Becker C-Bow side bags and panniershigh-quality surface finishnormal Hepco&Becker hard cases such as the Junior or Journey do not fit!Krauser K-Wing cases do not fit on the C-Bow carrier!Recommended payload: 5kg per bag/case (please observe the fitting instructions, vehicle-specific information and motorbike manufacturer's specifications for any restrictions that may apply)can usually be combined with top case carriers, sissy bars or solo racks without any problems (please observe the installation instructions or the vehicle-specific information for the respective carrier)Luggage rack extensions can restrict bag mounting on the carrierNo ABE or registration is required for this product if fitted as intendedScope of delivery: left, right, mounting material and instructionsDeveloped for the standard condition of the machine. Not tested with accessories such as exhaust, licence plate holder or other indicators. Make sure that the bags always have sufficient distance to the exhaust and that the indicators have a sufficient beam angle. The exhaust jet must not be directed at the bags.
Side case carrier fixed black for Moto Guzzi V7 III (Stone, Special, Anniversario, Racer) (2017-2020)
The bolt-on side case carriers from Hepco&Becker are firmly attached to the motorbike frame. Almost all Hepco&Becker touring side case systems fit onto this carrier. The cases are secured to the carrier using a metal retaining lock to prevent theft. A lock adapter is also required for this. This is normally supplied with the side cases. This lock adapter is screwed to the right and left at the rear of the carrier and provides the mount for the case retaining lock.The model-specific carriers are solidly designed and offer effective protection for the rider's or pillion passenger's legs even in the event of a fall.The side case carriers from Hepco&Becker can usually be combined with our rear carriers without any problems. Please refer to the fitting instructions and the model-specific information.Tubular steel construction MADE IN GERMANYfirmly bolted to the motorbike framehigh-quality surface finishFits most Hepco&Becker hard-shell side cases (please refer to the model-specific instructions for the respective carrier for any restrictions that may apply)Indicators usually remain in their original position, but sometimes have to be moved to ensure a certain beam angle (please refer to the installation instructions for the product)Scope of delivery: right + left incl. mounting material and instructionsLuggage systems generally do not require an ABE or registrationTube diameter: 16 mm
Chrome tubular luggage rack top case carrier for Moto Guzzi V7 III (Stone, Special, Anniversario, Racer) (2017-2020)
Proven tubular luggage racks Top case carriers for Hepco&Becker top cases of the highest quality. Hepco&Becker luggage racks are specially designed for almost all of our top cases. But not only new top cases fit. Older Hepco&Becker models can also be fitted. The basic mount has not changed. Not suitable for: Topcase "Orbit" and topcases with universal plate. The carriers are manufactured specifically for each model and only fit the motorbike listed in the fitting instructions. Thanks to the construction made of German quality steel, Hepco&Becker luggage racks guarantee maximum strength and a very high level of safety. If required, soft luggage can also be lashed down without any problems; the tubular luggage rack offers many options for this. If there is still not enough space, the luggage rack can be combined with the Hepco&Becker universal luggage rack extension. The top case is pushed onto the tubular luggage rack and locked to the carrier with a metal retaining lock. Recommended payload: approx. 5kg (Please observe the model-specific information on the respective carrier as well as the motorbike manufacturer-specific information) Can usually be combined with side case carriers or C-Bow holders without any problems (follow the fitting instructions) Incl. mounting material and instructions MADE IN GERMANY Luggage carriers generally do not require an ABE or registration
Tubular luggage rack Topcaseträger black for Moto Guzzi V7 III (Stone, Special, Anniversario, Racer) (2017-2020)
Proven tubular luggage racks Top case carriers for Hepco&Becker top cases of the highest quality. Hepco&Becker luggage racks are specially designed for almost all of our top cases. But not only new top cases fit. Older Hepco&Becker models can also be fitted. The basic mounting has not changed. Not suitable for: Topcase "Orbit" and topcases with universal plate. The carriers are manufactured specifically for each model and only fit the motorbike listed in the fitting instructions. Thanks to the construction made of German quality steel, Hepco&Becker luggage racks guarantee maximum strength and a very high level of safety. If required, soft luggage can also be lashed down without any problems, the tubular luggage rack offers many options for this. If there is still not enough space, the luggage rack can be combined with the Hepco&Becker universal luggage rack extension. The top case is pushed onto the tubular luggage rack and locked to the carrier with a metal retaining lock. Recommended load: approx. 5kg (Please note the model-specific information on the respective carrier and the motorbike manufacturer's specifications) Can usually be combined with side case carriers or C-Bow holders without any problems (follow the fitting instructions) Incl. mounting material and instructions MADE IN GERMANY Luggage carriers generally do not require an ABE or registration
Matching Universal-Products
Our novelty for individual design: The Drybrid BagFeatures of the Drybrid:Wide opening with roll-top closure and plastic clips on the sidesTwo circumferential compression strapsWaterproofSuitable for many motorcycles due to lashing with 4 loop strapsCan be mounted on pillion seat and wideningUV resistantEasy to cleanEasy to compress due to side air valveWith practical carrying handleShoulder strap available as an optionDetails of the DrybridMaterial: PVC coated polyesterColor: gray-black / reflex External dimensions 30L: 26 x 34 x 45cm Weight: 0.9kg Packing volume: 30 litersIncludes loop straps for universal use 4 point attachment
Our novelty for individual design: The Drybrid BagFeatures of the Drybrid:Wide opening with roll-top closure and plastic clips on the sidesTwo circumferential compression strapsWaterproofSuitable for many motorcycles due to lashing with 4 loop strapsCan be mounted on pillion seat and wideningUV resistantEasy to cleanEasy to compress due to side air valveWith practical carrying handleShoulder strap available as an optionDetails of the DrybridMaterial: PVC coated polyester Color: gray-black / reflex External dimensions: 32 x 32 x 52cm Weight: 1.0kg Packing volume: 50 litersIncludes loop straps for universal use 4 point attachment
Hepco&Becker Royster Rearbag incl. Seatpad Basic The seatpad is attached to the pillion seat or pillion bench using straps. The Basic counterholder is screwed to the base of the rear bag, allowing the rear bag to be simply clicked onto the Seatpad Basic and removed again quickly and easily. Scope of delivery: 1x rear bag, 1x Seatpad Basic, 1x Basic counterholder (locking unit)stable and secure hold thanks to rubber plate on the seat padRear bag is suitable for a helmet thanks to the extension zip Rear bag with waterproof inner bag, water-repellent outer materialnot suitable for off-road use
The Hepco&Becker Royster Rearbag Sport incl. Seatpad Basic The seat pad is attached to the pillion seat or pillion bench using straps. The Basic counterholder is screwed to the base of the rear bag, allowing the rear bag to be simply clicked onto the Seatpad Basic and removed again quickly and easily.Scope of delivery: 1x rear bag, 1x Seatpad Basic, 1x Basic counterholder (locking unit)stable and secure hold thanks to rubber plate on the seat padRear bag with waterproof inner bag, water-repellent outer materialRear bag with extension zipnot suitable for off-road use
Street rear bag incl. Seatpad BasicThe seat pad is attached to the pillion seat or pillion bench using straps. The Basic counterholder is screwed to the base of the rear bag, allowing the rear bag to be simply clicked onto the Seatpad Basic and removed again quickly and easily. Scope of delivery: 1x rear bag, 1x Seatpad Basic with straps, 1x Basic counterholder (locking unit) stable and secure hold thanks to rubber plate on the seat pad Rear bag with integrated rain cover, carrying handle, shoulder strap and rubber luggage net on the lid Rear bag has reinforced side walls to retain its shape, sturdy EVA base shell, 2-way zip, lockable with small padlock and all-round zip to increase volumenot suitable for off-road use
Universal fit for almost all motorbikesBelt set included in the scope of deliveryReliable 4-point tensioning strap fastening2 outer pockets with zipsZipped mesh compartment in the lid Covered zips Underside made of non-slip material Water-repellent outer material with inner coating Reflective details for better visibility Waterproof inner pocket with roll-top closure Robust carry handle G-Hook fastening elements made from anodised aluminium High-strength bartack seams Hypalon zip for better grip