With the Nova LED additional headlight set from HEPCO&BECKER you get everything you need to improve the visibility and safety of your motorcycle. This set contains powerful LED additional headlights, a universal mounting set, a cable set, a switch, instructions and a tool set to conveniently mount and control the headlights. The Nova LED additional headlights not only offer improved illumination of the road, but also give your motorcycle an attractive look. Easy installation is made possible by the included universal mounting set and cable set. Increase your safety and add an attractive design to your motorcycle by using the HEPCO&BECKER LED additional headlight set Nova. High-power LEDs with two switching levels at 2,500lm - 4,350K / - 5,500K12 volts, per headlight 22 watts ECE tested and approved, therefore no individual approval is required (observe country-specific legal regulations for installation) Improved traffic light conditions Universal attachment to engine or tank protection bar with tube Ø18mm – Ø25mm, can be attached standing or hanging Complete headlight set; Incl. 2x LED additional headlights, 1x switch, 1x cable set, 2x clamp incl. reducing sleeves, 1x instructions, 1x tool set Connection is only via the battery, no connection to the vehicle wiring harness is required No external operation by third parties, thanks to a special control unit with automatic voltage controlWaterproof and dustproof to IP67Headlights can be flexibly switched on using the switch on the handlebarsNote: The lights can only be switched on approx. 5-15 seconds after the engine has been started. A voltage of 13.1 V must be applied to the control unit of the wiring harness to enable the circuit. In older vehicles, this can be achieved by briefly increasing the engine speed. Switching off must be done manually using the switch. The NOVA LEDs continue to light up until the voltage limit of 11.3 V is reached, even after the engine is switched off. Only when the voltage falls below this limit do the lights switch off automatically via the control unit. When switching on again (wait for the time limit of control unit), the voltage limit of 13.1 V is queried again.

Steady. Stable. Easy to work. The HEPCO&BECKER center stands are extremely rugged and don't get in the way of your riding. The tension springs are made of stainless steel. Sophisticated geometry and anti-skid tread make it easy to stand your motorcylcle securely in any situation. The precisely manufactured stands are very stable, sandblasted, black powder coated and hold their value. Naturally, the're approved for the street. Center stands make maintenance easier and keep the bike stable, during fill-ups, for example. During winter storage, they take a load off the rear wheel.does mostly not limit bankingpricise manufacturingeasy assemblyQuality German steel tubingAccessories available: Special tool for fitting the spring more easily. part no: 700030Please also check manual for more info

Both when driving off-road and on asphalt, the Hepco&Becker grip protection ensures reliable protection of the driver's hands and the motorcycle handlebars. powder-coated solid tubular steel construction Made in Germany Scope of delivery: right + left + instructions + mounting material usually only fits vehicles with original handlebar clamps please note the installation instructions and the vehicle-specific information If a handlebar riser is installed, installation is also possible in most cases. Depending on the handlebar riser, longer screws are required for assembly. You have to get these screws yourself, as we don't have all the screws in all the right lengths.

Ideal for extreme terrain: the tank guard Rally, which stands out due to its 5-point connection to the motorcycle frame and additional stiffening plates at the lower node. The 2-fold front joining and bolting of the tube-halves leads to an optimal distribution of forces in the event of an overturn or fall. Close-fitting and sporty design with the best possible force dissipation into existing frame points. The bracket can be combined with the original skid plate. The innovative design with the high-strength plastic coating is unmistakable. With the function clearly in focus, it becomes clear: this tank guard was developed for tough, uncompromising use in difficult terrain. protection during pushovers or falls helps to tying up the motorcycle premium surface finish easy assembly delivery: right side, left side, mounting kit and manual high quality german steel tube please check manual or bike specific note for more info