YAMAHA Ténéré 700 World Raid Accessories

Let there be light! Motorbike auxiliary headlights LED NOVA With the Nova LED auxiliary headlight set from HEPCO&BECKER, you get everything you need to improve the visibility and safety of your motorbike. This set includes powerful LED auxiliary headlights, a universal mounting set, a cable set, a switch, instructions and a tool set to conveniently mount and control the headlights. The Nova LED auxiliary headlights not only provide improved illumination of the road, but also give your motorbike an attractive appearance. Easy installation is made possible by the universal mounting kit and cable set supplied. Increase your safety and add an appealing design to your motorbike by using the HEPCO&BECKER LED motorbike auxiliary headlight set Nova. The brand new LED auxiliary headlight Nova - the next step in lighting technology. High-power LEDs with two switching levels at 2,500lm - 4,350K / - 5,500K 12 volt, 25 watts per headlight ECE-tested and approved, so no individual approval is required (observe country-specific legal regulations for installation) Improved lighting conditions in road traffic Universal mounting on engine or tank protection bracket with Ø18mm - Ø25mm tube, can be mounted upright or suspended complete headlight set; incl. 2x LED auxiliary headlights, 1x switch, 1x cable set, 2x clamps incl. reduction sleeves, 1x instructions, 1x tool set Connection only via the battery, no connection to vehicle wiring harness required No third-party operation thanks to special control unit with automatic voltage control Waterproof and dustproof to IP67Headlights can be added flexibly via the switch on the handlebarsPlease note: The lights can only be switched on approx. 5-15 seconds after starting the engine. A voltage of at least 13.1 V must be applied to the control unit of the wiring harness to enable the circuit . In older vehicles, this can be achieved by briefly increasing the speed. Switching off must be done manually at the switch. The NOVA LEDs remain lit until the voltage limit of 11.8 V is reached, even after the engine has been switched off. Only when falls below this voltage limit do the lights switch off automatically via the control unit. When switching on again (wait for the dwell time of the control unit), the voltage limit of 13.1 V is queried again. Download FAQ as PDF

Additional luggage space on the engine and tank protection bars for items that no longer fit in the tank bag but still need to be within reach. Simply slide it onto the mudguard and attach it securely to the bracket using the full-surface Velcro fastening. for universal attachment to engine and petrol tank guards extremely high dimensional stability low weight abrasion-resistant coating water-repellent and incl. small waterproof inner pocket lockable 2-way zip Recommended max. speed: 130 km/h (please observe the service information on the bag and the motorbike-specific manufacturer's specifications) Luggage systems generally do not require an ABE or registration

Tank protection: crash bar for Yamaha Ténéré 700 World Raid from Hepco & Becker Whether you prefer to ride off-road, even in difficult terrain, freely on country roads or spend most of your time in the city, a motorbike crash bar is no longer a beginner's accessory. Developed for a wide range of motorbikes, our crash bars fit perfectly into the existing lines of your Yamaha Ténéré 700 World Raid, giving the motorbike a characteristic look, but more than just that: in the event of a crash or unintentional contact with the ground, our motorbike crash bars also protect the rider from more serious damage! Crash bars from Hepco&Becker are the right choice for all individualists who value safety and quality. Made from an extremely stable tube-in-tube construction, manufactured from German quality steel or stainless steel, they offer maximum protection - with many newer models already featuring an integrated crash pad.Exclusive look thanks to high-quality surface finish: High-quality powder coating from Germany.And last but not least, motorbike crash bars also offer you many other options for additional comfort, for example you can attach our protective bar bags to them, or our additional/fog lights.On top of this, motorbike crash bars are incredibly well suited for securely lashing your bike to a trailer if you ever need to transport it. Features & details: Material: Tubular steel made in GermanySurface finish: High-quality powder coatingColour: BlackFor model year(s): 2022-2024Provides effective protection in the event of minor accidents or mishaps Extremely helpful when lashing the motorbike, e.g. on trailers Scope of delivery: Tank guard for Yamaha Ténéré 700 World Raid leftTank guard for Yamaha Ténéré 700 World Raid right Screw set (incl. spacers, sleeves, washers etc.) Multilingual, comprehensive illustrated assembly instructions Important notes: No ABE or registration is required for this product if fitted as intended Please observe the model-specific information listed in the installation instructions and properties! Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! For safety reasons, all mudguards should be adequately checked after a crash and replaced if necessary. If original or accessory parts have already been fitted, there may be restrictions; these can be found in the fitting instructions. We offer special conditions for official driving schools. Please contact our customer service at (+49) 0 6331 / 1453 - 222

Inner dimensions: 29x8 cm (length/diameter) Outer dimensions: 32x9 cm Volume: approx. 1.5 litres mounted on the inside of a side case carrier to utilise this space for specific models a model-specific mounting kit is included as fastening material waterproof twist lock perfect for carrying tools, safety waistcoats or similar items.

A whirled up stone on off-road passages often means the end for the expensive headlight. Our Hepco&Becker lamp guard protects the headlight in many cases and also gives your bike the appropriate off-road look.adapted to the design of the motorbikeeffective protectionno reflections or danger from glaresimple mounting on mostly existing screw pointsrobust and high-quality coatingmade in Germany without TÜV

Motorbike underride guard: engine protection plate for Yamaha Ténéré 700 World Raid (2022-2024), black Even a pavement can mean unpleasant and heavy contact with the ground, which can lead to damage to the engine housing. Our engine protection plates protect the manifold and engine block from impacts and stone chipping, even with the heaviest ground contact. With our underride guard for Ténéré 700 World Raid, you not only upgrade your motorbike in terms of safety, but also automatically give it a certain off-road look. Naturally manufactured specifically for each model from approx. 4 mm thick, high-strength aluminium, our Hepco&Becker engine protection plate lets enough air through for cooling thanks to its special shape and is naturally angled, so that water such as rainwater or splash water is drained to the outside, thus providing additional protection against rust formation. It enhances the look of your motorbike and is guaranteed never to let you down Features & important details: Material: High-strength aluminium, made in Germany Surface finish: Brushed, anodised Colour: Black anodisedFor model year(s): 2022-2024Provides additional protection for sensitive parts on the manifold and engine block Scope of delivery: Engine protection plate for Yamaha Ténéré 700 World RaidMounting material / screw set Illustrated installation instructions (DE / EN) Important notes: No ABE or registration is required for this product if fitted as intended Please observe the fitting instructions and model-specific information to determine whether there may be any restrictions. Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! Restrictions may apply to original parts or accessories that have already been fitted; these can be found in the fitting instructions.

Stable. Stable. Easy to use. The centre stands from Hepco&Becker usually do not restrict the rider's lean angle and are extremely robust. Thanks to the sophisticated geometry and non-slip tread surface, it is very easy to park the motorbike safely in any situation.The precisely manufactured stands are very stable, sandblasted, primed and black powder-coated and therefore weatherproof and stable in value. Main stands simplify maintenance work and ensure a secure stand, e.g. when refuelling. They relieve the load on the suspension elements and the rear wheel during winter storage.ABE is suppliedusually no restriction on lean angle clearancehigh-quality surface finishScope of delivery: Main stand + mounting material + instructionsplease note the installation instructions providedHelpful tool for attaching the tension spring: item number: 700030

Grip protection for Yamaha Ténéré 700 World Raid or World Rally - by Hepco&Becker The Hepco&Becker grip guard guarantees reliable protection for the rider's hands and the motorbike handlebars both when riding off-road and on asphalt. Model-specific hand protector guard for your Yamaha Ténéré 700 World Raid / Rally - Tubular steel construction precisely customised to your motorbike for the perfect look. Ideal for all adventure bikes to stabilise the hand protectors and protect them from breakage in the event of a crash or contact with a large branch, for example! Reliable, robust protection for the handlebar fittings in the event of a crash with optimum aerodynamics. As individual as you are - make it your bike! Details & features: Material: Tubular steel, made in Germany Surface finish: High-quality, colour-matching powder coating Colour: black For model years: World Raid: 2022-2024 or World Rally: 2023 & 2024 Scope of delivery: 1 set of grip guards (left & right) Complete set of mounting material Bilingual, illustrated assembly instructions Important notes: The plastic hand protectors shown in the pictures are part of the delivery condition of the motorbike, they are NOT included! Please observe the model-specific information listed in the fitting instructions and the features! Unless explicitly stated otherwise, our model-specific products are only developed for the standard condition of the motorbike! May not fit in combination with non-original handlebar clamps, e.g. with comfort handlebars or handlebar risers! For safety reasons, all protective bars should be adequately checked after a fall and replaced if necessary.

Side stand extension Yamaha Ténéré 700 World Raid (2022-2024) To widen the contact surface of the side stand - for absolutely secure standing on gravel, sand, crushed stone, etc. Quick and easy to fit, made from high-quality CNC-milled aluminium with a powder-coated steel counter support - Made in Germany. Especially when fully loaded or on unpaved surfaces, the motorbike can easily sink and tip over on the side stand. To free your motorbike from this danger, we recommend a model-specific, moulded side stand plate from Hepco&Becker. The side stand support is enlarged to approximately double the surface area compared to the original stand, so your Ténéré 700 World Raid is perfectly protected from mishaps when parking. Material: Aluminium & powder-coated steel Colour: silver / black Developed specifically for the Yamaha Ténéré 700 World Raid For model year(s): 2022, 2023, 2024 Effective protection when parking Quick and easy installation with just a few screws ABE & registration free

Basic tank ring for Yamaha Ténéré 700 World Raid (2022-2024) /World Rally (2023-2024)Simple and innovative at the same time - our BASIC tank ring This functional tank ring enables the attachment of a Hepco&Becker tank bag.The scope of delivery includes a BASIC tank ring and the counterholder, which can be individually screwed to the tank bag depending on the tank shape and handlebar angle. The tank cap can still be opened without any problems when the tank ring is fitted. In general, you only need this tank ring and a tank bag for Yamaha Ténéré 700 World Raid (2022-2024) /World Rally (2023-2024) and you have everything you need. Each model-specific tank ring is stored in the "My Bike" database for the respective motorbike model. If no tank ring is stored, you can also use the checklist here in the shop to find out manually whether a universal tank ring is available for the desired model. (See main menu -> BASIC tank rings) FEATURES: absolutely secure hold, even at high speeds Simple operation thanks to mechanical locking the Hepco&Becker tank bag is simply put on and locks clearly audible on the tank ring Unlocking: The mechanism is unlocked by a strap at the front of the tank bag in the direction of travel and the tank bag is then simply removed No ABE or registration is required for this product when fitted as intended Recommended maximum speed when the tank bag is fitted: 130 km/h Recommended load in the tank bag: approx. 3kg Please observe the motorbike manufacturer's specifications and the model-specific information in the instructions or here with the product Difference between Lock-it and BASIC tank rings: The general function and operation remain the same. However, compared to the Lock-it tank ring, the Basic tank ring only locks mechanically. With the Lock-it tank ring, the magnets help with centring. The difference lies purely in the two magnetic or plastic domes that are screwed onto the tank ring. The actual model-specific "metal ring" is the same for both versions. Further information: A tank bag with Lock-it counterholder cannot be fitted to a BASIC tank ring and vice versa. The tank bag counterholder and tank ring must be from the same system.

The bolt-on side case carriers from Hepco&Becker are firmly attached to the motorbike frame. Almost all Hepco&Becker touring side case systems fit onto this carrier. The cases are secured to the carrier using a metal retaining lock to prevent theft. A lock adapter is also required for this. This is normally supplied with the side cases. This lock adapter is screwed to the right and left at the rear of the carrier and provides the mount for the case retaining lock.The model-specific carriers are solidly designed and offer effective protection for the rider's or pillion passenger's legs even in the event of a fall.The side case carriers from Hepco&Becker can usually be combined with our rear carriers without any problems. Please refer to the fitting instructions and the model-specific information.Tubular steel construction MADE IN GERMANYfirmly bolted to the motorbike framehigh-quality surface finishFits most Hepco&Becker hard-shell side cases (please refer to the model-specific instructions for the respective carrier for any restrictions that may apply)Indicators usually remain in their original position, but sometimes have to be moved to ensure a certain beam angle (please refer to the installation instructions for the product)Scope of delivery: right + left incl. mounting material and instructionsLuggage systems generally do not require an ABE or registrationTube diameter: 16 mm

C-Bow side bag holder for Yamaha Ténéré 700 World Raid (2022-2024) /World Rally (2023-2024) is designed to accommodate a wide range of Hepco&Becker Bags. Softbags for sporty, dynamic motorbikes and saddlebags for choppers and cruisers can be attached to the motorbike with the C-Bow holder. Its elegant, unobtrusive design blends in perfectly with the overall lines of the vehicle. Naturally, it keeps the saddlebags safely away from the hot exhaust silencer. Thanks to modern C-Bow technology, the matching bags can be attached to the C-Bow simply and easily with just one click and locked to prevent theft. The bags are securely fastened to the motorbike and remain in position even when loaded. On many models, the indicators remain in their original position. Further information can be found in the fitting instructions.solid side carrier for mounting Hepco&Becker C-Bow side bags and panniershigh-quality surface finishnormal Hepco&Becker hard cases such as the Junior or Journey do not fit!Krauser K-Wing cases do not fit on the C-Bow carrier!Recommended payload: 5kg per bag/case (please observe the assembly instructions, vehicle-specific information and motorbike manufacturer's specifications for any restrictions that may apply)can usually be combined with top case carriers, sissy bars or solo racks without any problems (please observe the installation instructions or the vehicle-specific information for the respective carrier)Luggage rack extensions can restrict bag mounting on the carrierNo ABE or registration is required for this product if fitted as intendedScope of delivery: left, right, mounting material and instructionsDeveloped for the standard condition of the machine. Not tested with accessories such as exhaust, licence plate holder or other indicators. Make sure that the bags always have sufficient distance to the exhaust and that the indicators have a sufficient beam angle. The exhaust jet must not be directed at the bags.

Sturdy aluminium plate for widening on almost all luggage racks with a straight support surface if loose luggage is to be transported rather than a top case. The raised edges and additional retaining points make the extension ideal for safely transporting larger luggage rolls, travel bags, tents, duffle bags, etc.Aluminium construction with high strength and high-quality appearanceFastening options for strapsNot suitable for topcase mountingincludes assembly material and instructionshigh-quality plastic coatingRecommended load: 5kg (Please observe the model-specific instructions and the motorbike manufacturer's specifications. Heavy luggage should generally not be transported on the rear, but in the side cases or the tank bag.

Handlebar riser for Yamaha Ténéré 700 World Raid (2022-2024) / World Rally (2023-2024) by Hepco&Becker With the help of handlebar risers and handlebar risers with offset, you can adjust the seating position on the motorbike to suit you and therefore ride in a more relaxed and comfortable manner. The handlebar risers and handlebar relocations fit seamlessly and unobtrusively into the overall line of the motorbike. simple installation naturally TÜV-tested and incl. ABE high quality precisely milled, model-specific handlebar risers for use with original upper clamps

The slim, lightweight and unobtrusive luggage solution from Hepco&Becker. The Smartrack offers a way to individually attach soft luggage to the rear of the motorbike. A rucksack or bag can be lashed through the side slots. Our rear panniers with the Basic System can also be easily attached to it using an interchangeable module. suitable for rear panniers with Basic attachmentflexibleincl. screw set and installation instructionsaBE or registration is not necessaryhigh-quality powder coatingsolid construction

Motorbike model-specific holder for mounting various Hepco&Becker top cases (top cases with universal plate do not fit) Topcase carrier consisting of a model-specific mounting kit and the Easyrack adapter plate for mounting Hepco&Becker topcases or soft luggage (not suitable for topcases with universal plastic plate or Orbit topcase) Hepco&Becker Easyracks are specially designed for our topcases. As the successor to the tried and tested tubular luggage racks, the Easyrack is seen as a logical further development and is available for the younger generation of motorbikes. Each Easyrack top case carrier is developed specifically for each model and therefore blends in harmoniously with the overall appearance of the motorbike. Thanks to the production from high-quality aluminium in combination with a steel base carrier, the Easyrack has a high level of strength and a very elegant appearance. Additional fastening points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack. solid construction Scope of delivery: model-specific Easyrack top case carrier + mounting kit + mounting instructions no additional adapters are required for top case mounting high-quality surface finish Recommended payload: 5kg payload in the top case (please observe vehicle-specific information, the stored assembly instructions and motorbike manufacturer information) technically almost identical to the Alurack top case carrier, except that the bracket for holding the top case can be folded down when a top case is not in use the model-specific base carrier is the same for the Easyrack and Alurack Orbit top case and universal top cases with plastic pallet do not fit Luggage carriers do not require an ABE or registration

Side case carrier cutout for Yamaha Ténéré 700 World Raid (2022-2024) /World Rally (2023-2024)Motorbike luggage carrier features:adventure-compatible, weather-resistant and bolted stainless steel pannier rackblasted and electropolished surface finishScope of delivery: left, right, mounting material and instructionsonly the Xplorer cases 40 Cutout and 37 Cutout can be attached to this carriernormal Xplorer cases and other Hepco&Becker cases do not fit

With the help of handlebar risers and handlebar risers with offset, you can adjust the seating position on the motorbike to suit you and therefore ride in a more relaxed and comfortable manner. The handlebar risers and handlebar relocations fit seamlessly and unobtrusively into the overall line of the motorbike. simple installationNaturally TÜV-tested and incl. ABEhigh qualityvarious designs depending on the model: Distances or sleeves under the handlebar clamps; handlebar risers under the handlebars for use with original upper clamp; handlebar risers with lower and upper clamps

Case carrier set for Yamaha Ténéré 700 World Raid (2022-2024) /World Rally (2023-2024) incl. Xplorer motorbike case, blackSet consisting of a double-sided, motorbike model-specific stainless steel case carrier in combination with an Xplorer 40 and a recessed Xplorer 37 side case incl. key, lock cylinder and the required lock adapters to attach the cases to the carrierMotorbike side case features:recessed 37 litre case on the end pot side40 litre case on the other sidehighly impact-resistant plastic and anodised aluminium sheets in combinationincl. key and cylinderabsolutely watertight thanks to integrated rubber seal in the lidextensive range of accessories available (inner bags, top bags, etc.)Motorbike luggage carrier features:adventure-ready, weather-resistant and bolted stainless steel pannier rackblasted and electropolished surface finishincl. mounting material and assembly instructions

Case carrier set for Yamaha Ténéré 700 World Raid (2022-2024) /World Rally (2023-2024) incl. Xplorer motorbike case, silverSet consisting of a double-sided, motorbike model-specific stainless steel case carrier in combination with an Xplorer 40 and a recessed Xplorer 37 side case incl. key, lock cylinder and the lock adapters required to attach the cases to the carrierMotorbike side case features:recessed 37 litre case on the end pot side40 litre case on the other sidehighly impact-resistant plastic and anodised aluminium sheets in combinationincl. key and cylinderabsolutely watertight thanks to integrated rubber seal in the lidextensive range of accessories available (inner bags, top bags, etc.)Motorbike luggage carrier features:adventure-ready, weather-resistant and bolted stainless steel pannier rackblasted and electropolished surface finishincl. mounting material and assembly instructions

Top case carrier consisting of a model-specific mounting kit and the Alurack adapter plate for mounting Hepco&Becker top cases or soft luggage (not suitable for top cases with universal plastic plate) Hepco&Becker Aluracks are specially designed for our top cases. As the successor to the tried and tested tubular luggage racks, the aluminium rack is seen as a logical further development and is available for the younger generation of motorbikes. Each Alurack top case carrier is developed specifically for each model and therefore blends in harmoniously with the overall appearance of the motorbike. Thanks to the production from high-quality aluminium in combination with a steel base carrier, the Alurack has high strength and a very elegant appearance. Additional fastening points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack.solid constructionScope of delivery: model-specific aluminium top case carrier + mounting kit + mounting instructionsno additional adapters are required for top case mountinghigh-quality surface finishRecommended payload: 5kg payload in the top case (please observe vehicle-specific information, the stored assembly instructions and motorbike manufacturer information)technically almost identical to the Easyrack top case carrier, except that the bracket for holding the top case is rigidly positioned upwardsthe model-specific base carrier is the same for the Easyrack and Aluracka special bracket is required to mount the aluminium standard top case 35 (article number: 700007350 or 700007351)Luggage carriers do not require an ABE or registration