With the Nova LED additional headlight set from HEPCO&BECKER you get everything you need to improve the visibility and safety of your motorcycle. This set contains powerful LED additional headlights, a universal mounting set, a cable set, a switch, instructions and a tool set to conveniently mount and control the headlights. The Nova LED additional headlights not only offer improved illumination of the road, but also give your motorcycle an attractive look. Easy installation is made possible by the included universal mounting set and cable set. Increase your safety and add an attractive design to your motorcycle by using the HEPCO&BECKER LED additional headlight set Nova. High-power LEDs with two switching levels at 2,500lm - 4,350K / - 5,500K12 volts, per headlight 22 watts ECE tested and approved, therefore no individual approval is required (observe country-specific legal regulations for installation) Improved traffic light conditions Universal attachment to engine or tank protection bar with tube Ø18mm – Ø25mm, can be attached standing or hanging Complete headlight set; Incl. 2x LED additional headlights, 1x switch, 1x cable set, 2x clamp incl. reducing sleeves, 1x instructions, 1x tool set Connection is only via the battery, no connection to the vehicle wiring harness is required No external operation by third parties, thanks to a special control unit with automatic voltage controlWaterproof and dustproof to IP67Headlights can be flexibly switched on using the switch on the handlebarsNote: The lights can only be switched on approx. 5-15 seconds after the engine has been started. A voltage of 13.1 V must be applied to the control unit of the wiring harness to enable the circuit. In older vehicles, this can be achieved by briefly increasing the engine speed. Switching off must be done manually using the switch. The NOVA LEDs continue to light up until the voltage limit of 11.3 V is reached, even after the engine is switched off. Only when the voltage falls below this limit do the lights switch off automatically via the control unit. When switching on again (wait for the time limit of control unit), the voltage limit of 13.1 V is queried again.

Whether you ride more on rugged terrain, on country roads or in town; a HEPCO&BECKER guard is always the right choice. Your motorcycle is always effectively protected against an unexpected mishap.And even more: If the bike falls over or makes unintentional contact with the ground, it can protect both, bike and rider from more serious consequences.HEPCO&BECKER protection bars follow the lines of the bike perfectly, giving it a customized appearance. Made with extremely stable tube-in-tube construction. Depending on the vehicle model, various surface finishes are available.protection during pushovers or fallshelps, when tying up the motorcyclepremium surface finisheasy assemblydelivery: right side, left side, mounting kit and manualhigh quality german steel tubeplease check manual or bike specific note for more info

Just fully packed, or on unstable ground, the motorcycle threatens to sink easily on the side stand.A precisely shaped milled spreading plate, which is quickly screwed to the side stand and freed from this dangeris now available! More than 100% larger surface area Safe stand of the machine on all surfaces Oxidation-proof black anodised

Both when driving off-road and on asphalt, the Hepco&Becker grip protection ensures reliable protection of the driver's hands and the motorcycle handlebars. powder-coated solid tubular steel construction Made in Germany Scope of delivery: right + left + instructions + mounting material usually only fits vehicles with original handlebar clamps please note the installation instructions and the vehicle-specific information If a handlebar riser is installed, installation is also possible in most cases. Depending on the handlebar riser, longer screws are required for assembly. You have to get these screws yourself, as we don't have all the screws in all the right lengths.

The C-Bow bag holder is made to take a variety of Hepco&Becker bags, depending on the motorcylce model. Softbags for sporty, dynamic motorcycles and saddlebags for choppers and cruisers can be attached to the motorcycle with the C-Bow holder. Its elegant, unobtrusive design fits perfectly into the vehicles overall lines. Naturally, it keeps saddlebags safely away from the hot exhaust muffler. Modern C-Bow technology allows the right bags to be attached simply and easily to the C-Bow with a single click, firmly locking them to deter theft. The bags are attached securely to the motorcycle and stay in position even when loaded. On many models, the turn signals stay in their original position. Please check manual for more info.special carrier only for Hepco&Becker C-Bow bags and boxesnormal Hepco&Becker hard luggage does not fitKrauser K-Wing hard luggage does not fiteasy mountingdelivery: right side, left side, mounting kit, manualrecommended load: 5kg per bag (please check manual or motorcycle manufacturer for more info)can mostly be combined to topcasecarrier, sissybars or other rear carrier (please check manual or bike specific info)rear rack enlargements can possibly restrict the function of the bags

Simple and innovative at the same time - the BASIC tank ring This functional tank ring allows you to attach a tank bag from Hepco&Becker.The scope of delivery includes a BASIC tank ring, as well as the fastener for tankbags, which can be individually screwed to the tank bag, depending on the shape of the tank and the angle of the handlebars. The tank cap can still be opened with the tank ring mounted without any problems. In general, all you need is this tank ring and a tank bag from H&B and you have everything you need.Each model-specific tank ring is stored in the "My Bike" database for the respective motorcycle model. If no tank ring is stored, you can also use the checklist here in the shop to find out manually whether a universal tank ring is available for the desired model. (See main menu -> tank rings BASIC)Characteristics:absolutely secure hold, even at high speedsmechanical lockingeasy handlingthe Hepco&Becker tank bag is simply put on and locks audibly on the tank ring thanks to a sophisticated mechanismunlocking: The mechanism is unlocked by a lashing strap in the direction of travel at the front of the tank bag; the tank bag is simply removedsimple but effective mechanicsrecommended maximum speed with the tank bag installed: 130 km/h (Please note the motorcycle manufacturer's information, as well as the model-specific information on the instructions or here with the productrecommended load in the tank bag: approx. 3kg In Germany, tank bag systems do not require an ABE or entry in the papers.Difference between Lock-it and BASIC tank rings:The general function and operation remains the same. Compared to the Lock-it tank ring, however, the Basic tank ring only locks mechanically. The magnets of the Lock-it tank ring help with centering. The difference lies purely in the two magnet or plastic domes, which are screwed onto the tank ring. The actual model-specific "metal ring" is the same for both versions.A notice:A tank bag with a Lock-it holder cannot be placed on a BASIC tank ring and vice versa. Tank bag holder and tank ring must be from the same system.

The slim, light and inconspicuous luggage solution from Hepco&Becker. The Minirack offers a way to individually attach soft luggage to the rear of the motorcycle. A backpack or bag can be lashed through side slits.solid steel tube carrierhigh quality aluminium plateeasy mountingincl. mounting kit and manualhigh quality surface finishthe Minirack system is also mentioned in our Topcasecarrier video:

The Hepco&Becker Alurack is especially designed for our top cases. As the successor to the luggage rack made of round tubing, the Alurack continues the tradition and is offered for later-generation motorcycles. This means you can attach nearly every Hepco&Becker top cases, wether aluminium or plastic and choose freely from the whole product line.Every Alurack is developed for the specific model and fits beautifully into the motorcycles overall look. Production from premium aluminium gives the Alurack great strengt and an elegant look. The Alurack design integrates additional luggage belt fastening points for attaching baggage rolls etc.recommended load: 5kg into the top case (please check manual and motorbike manufacturer for special info)Delivery: bike specific main frame, Alurack adapter, mounting kit, manualNo additional adapters needed for mounting a Hepco&Becker top caseAttention: Hepco&Becker top case with an universal plastic adapter plate do not fit. Only the normal Hepco&Becker top cases with a metal look on the bottomcan mostly be combined with C-Bow side carrier or normal hard lugagge side carrier: Please check manual or bike specific infoDifference to the Easyrack top case carrier: the bow which stands upwards for the top casemounting is rigidly fixed. Easyrack bow can be folded down.bike specific main frame is mostly the same at Alurack and EasyrackIf you want to mount Alu top case Standard 35, you need a special bow adapter: 700007351 or 700007350